Bronco.com HOME
 

---------

---------

RE: Axle wrap destroying my rear driveline?

From: Anthony Hernandez <ANTHONYH_at_jwce.com>
Date: Wed, 6 Feb 2002 11:39:09 -0800

Have you checked the bushings in your rear leaf springs?

-----Original Message-----
From: Craig Schneider [mailto:cischneider_at_hotmail.com]
Sent: Tuesday, February 05, 2002 5:03 PM
To: EBML_at_bronco.com
Subject: Re: [EBML] Axle wrap destroying my rear driveline?


  Given that I replaced my U-joints less than 6 mos. ago, and after I
removed my rear driveline last night the squeak went away, what else could
it be? Driving with only my front driveline in, has gotten rid of the
squeak (bad noise) and also the thump and settling motion that seems to
eminate from the rear of my rig when getting off my brakes. I must mention
that I am running a C4 so the rear will always be loaded except when in
Neutral.
  Any thoughts?
  Thanks,
  Craig


>From: "Brian Wickert" <bwickert_at_cnetech.com>
>To: "Craig Schneider" <cischneider_at_hotmail.com>, <EBML_at_bronco.com>
>Subject: Re: [EBML] Axle wrap destroying my rear driveline?
>Date: Tue, 5 Feb 2002 16:51:49 -0800
>
>It sounds like you are assuming the squeak is from the cv. Put the t-case
>in neutral, with the wheels chalked, and check the cv for lateral or
>vertical movement. Should be fairly solid.
>
>If you need a new driveshaft, you could probably get away with only
>allowing
>1" for compression (stiff springs/ shocks and ALOT of self control over
>railroad crossings). I'm guessing the 3.5" lift will only separate the
>driveshaft about 3/4". If you raise the vehicle 3.5" (yet another
>assumption), and the shaft sits around 20 degrees from horizontal, that is
>less then 1/4 of the vertical or 90 degree's of lift. I don't remember all
>the tangent/cosine stuff, but it works cause it is all relative and linear.
>
>Brian Wickert
>Hanford, CA
>http://www.bwickert.alloffroad.com/DusyErshim/DusyErshim.html
>http://www.bwickert.alloffroad.com/HydroBoost/HydroBoost.html
>http://www.bwickert.alloffroad.com/WreckingBall/WreckingBall.html
>http://www.bwickert.alloffroad.com/ClawHammer/ClawHammer.html
>http://www.bwickert.alloffroad.com/ARCA/ARCA.html
>http://www.bwickert.alloffroad.com/RockerBumpers/RockerBumpers.html
>http://www.bwickert.alloffroad.com/BroncoMods/BroncoMods.html
>http://www.bwickert.alloffroad.com/Fordyce/Fordyce.html
>http://www.vintagebronco.com/coby/images/bwickert/BWickert.html
>http://www.vintagebronco.com/coby/images/bwickert/jan27/atlas.html
>
>----- Original Message -----
>From: "Craig Schneider" <cischneider_at_hotmail.com>
>To: <EBML_at_bronco.com>
>Sent: Tuesday, February 05, 2002 4:11 PM
>Subject: [EBML] Axle wrap destroying my rear driveline?
>
>
> > Hey all,
> > I am faced with a dilemna that I would appreciate some input on...
> > After replacing the U-joints in my rear driveline approx 4 months ago,

>I
> > have resumed the same squeak and grind that was taken care of by
>replacing
> > the U-joints in the first place. I had not replaced the CV joint in the
> > driveshaft, only the U-joints that are on either side of the joint. I
>am
> > also noticing after running only my front driveline, that the wrap or
>thump
> > and thud that I had while running in rear wheel drive, has also
>disappeared.
> > I am assuming that I have major axle wrap and need to replace the stock
>rear
> > springs that have over 200K mi on them. My dilemna, I want to purchase
>a
> > 3.5" lift, but not now. If I am to replace my rear driveline, will one
>that
> > is a little longer for the lift work with my stock height set-up, and am

>I
> > in danger of ruining the new driveline with the axle wrap that I am
> > experiencing?
> > Any input would be appreciated.
> > Thanks in advance,
> > Craig in Fresno
> >
> > _________________________________________________________________
> > Send and receive Hotmail on your mobile device: http://mobile.msn.com
> >
> > ------------------------------
> > Early Bronco Mailing List (EBML)
> > Unsubscribe: majordomo_at_bronco.com unsubscribe EBML
>youremailid_at_yourisp.com
> > in the messagebody.
> > To modify your account (switch to digest or to real-time), goto:
> > http://mail.bronco.com/cgi-bin/mj_wwwusr/domain=bronco.com/EBML.
> > Admin address: EBML-owner_at_bronco.com
>


_________________________________________________________________
Join the world's largest e-mail service with MSN Hotmail.
http://www.hotmail.com

------------------------------
Early Bronco Mailing List (EBML)
Unsubscribe: majordomo_at_bronco.com unsubscribe EBML youremailid_at_yourisp.com
in the messagebody.
To modify your account (switch to digest or to real-time), goto:
http://mail.bronco.com/cgi-bin/mj_wwwusr/domain=bronco.com/EBML.
Admin address: EBML-owner_at_bronco.com
Received on Wed Feb 06 2002 - 12:44:48 MST


Email us at: info@bronco.com
Many thanks to our contributors.
© 1996 - 2016 www.Bronco.com