Bronco.com HOME
 

---------

---------

Re: [Bfix] Welder recomendations

From: Brett Kinch <kinchx4_at_earthlink.net>
Date: Wed, 6 Feb 2002 18:21:06 -0700

The Output Range of the Miller 210 is 30-210 amps. The Output Range of the
Lincoln 200 is 30-200 amps.
The Rated Output at 60% duty cycle is 160 amps for the Miller 210, and 150
amps for the Lincoln 200.....
Brett Kinch
Rock-Quip
www.rock-quip.rockcrawler.com



> You'd better check your facts again Brett. The Miller's "Output Range" is
> 210, not the actual or rated output which is only 160 amps whereas the
> Lincoln is 200. Both companies try to mislead you a bit. (Lincoln does
the
> same on their smaller welders.) They can get away with this as long as
they
> show the "Rated Output" somewhere. Buyer beware...
>
> Lee Wilson
> Houston, TX
> ----- Original Message -----
> From: "Brett Kinch" <kinchx4_at_earthlink.net>
> To: "bfix" <mail_at_broncofix.com>; "ebml" <ebml_at_bronco.com>
> Sent: Wednesday, February 06, 2002 6:02 PM
> Subject: Re: [Bfix] [EBML] Welder recomendations
>
>
> > The185 has been replaced by the 210 which is more powerful than
Lincoln's
> > 200.
> > Rated Output:
> > Miller 210--160 amps at 24.5 volts at 60% duty cycle
> > Lincoln 200-- 150 amps at 24 volts at 60% duty cycle
> > Interestingly, my Miller 185 has the same rated output as the Lincoln
200
> > except for 1 volt....
> > Miller 185-- 150 amps at 23 volts at 60% duty cycle
> > Hmmmm.............
> > Brett Kinch
> > Rock-Quip
> > www.rock-quip.rockcrawler.com
> >
> >
> >
> > > Kevin, good choice!!!!!! Ive used the Miller 185 and it cannot hang
with
> > my
> > > lincoln power mig. Mine cost me 50 bucks more than the 185 and its a
> true
> > > quality unit. And like Brian said, its got that cool Nascar sticker on
> > it!!!
> > > :)
> > >
> > >
> > > Clint
> > > ----- Original Message -----
> > > From: "Kevin Lackey" <lackkevi_at_inconnu.isu.edu>
> > > To: "Mike Bowlin" <live2wheel_at_msn.com>
> > > Cc: <EBML_at_bronco.com>; <mail_at_broncofix.com>
> > > Sent: Wednesday, February 06, 2002 1:19 PM
> > > Subject: Re: [Bfix] [EBML] Welder recomendations
> > >
> > >
> > > > I think after looking around I am going to get a Licoln PowerMig
200.
> I
> > > > found them for $1057.32 at www.weldingmart.com with free delivery. I
> > just
> > > > have to decide between at 200 amp and the 255 amp unit........ a
> little
> > > > more money.
> > > > Kevin
> > > >
> > > > --
> > > > Pereant, inquit, qui ante nos nostra dixerunt.
> > > >
> > > >
> > > >
> <><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><>
> > > > For Broncofix list addition and removal, go to
> http://www.broncofix.com
> > > > Check out our new message board at http://www.broncofix.com/board!!!
> > > > For additional assistance, email the admin at admin_at_broncofix.com
> > > >
> > >
> > >
> > >
> > > ######################################################################
> > > Attention:
> > > This e-mail message is privileged and confidential. If you are not the
> > > intended recipient please delete the message and notify the sender.
> > > Any views or opinions presented are solely those of the author.
> > > ######################################################################
> > >
> > >
> >
>
############################################################################
> > #########
> > > This e-mail message has been scanned for Viruses and Content.
> > >
> >
>
############################################################################
> > #########
> > >
> > >
<><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><>
> > > For Broncofix list addition and removal, go to
http://www.broncofix.com
> > > Check out our new message board at http://www.broncofix.com/board!!!
> > > For additional assistance, email the admin at admin_at_broncofix.com
> > >
> >
> > ------------------------------
> > Early Bronco Mailing List (EBML)
> > Unsubscribe: majordomo_at_bronco.com unsubscribe EBML
youremailid_at_yourisp.com
> > in the messagebody.
> > To modify your account (switch to digest or to real-time), goto:
> > http://mail.bronco.com/cgi-bin/mj_wwwusr/domain=bronco.com/EBML.
> > Admin address: EBML-owner_at_bronco.com
> >
>
> ------------------------------
> Early Bronco Mailing List (EBML)
> Unsubscribe: majordomo_at_bronco.com unsubscribe EBML youremailid_at_yourisp.com
> in the messagebody.
> To modify your account (switch to digest or to real-time), goto:
> http://mail.bronco.com/cgi-bin/mj_wwwusr/domain=bronco.com/EBML.
> Admin address: EBML-owner_at_bronco.com
>
Received on Wed Feb 06 2002 - 18:29:56 MST


Email us at: info@bronco.com
Many thanks to our contributors.
© 1996 - 2016 www.Bronco.com