Bronco.com HOME
 

---------

---------

Re: [Bfix] Welder recomendations

From: Brett Kinch <kinchx4_at_earthlink.net>
Date: Thu, 7 Feb 2002 07:25:45 -0700

uh...O.K.......
Brett Kinch
Rock-Quip
www.rock-quip.rockcrawler.com



> Well there you have it, the miller is equal to or better than the lincoln.
Its gotta be, says so
> right on the box.
> Mike Bowlin
> 67 EB narrowed 8"s...sefi 5.0,700r4,4.3 atlasII
>
> > O.K.....
> > You're getting your ratings and ranges confused, here....
> > You're comparing the Miller's output rating of a 60% duty cycle to
Lincoln's
> > max range of 200 amps at 30% duty cycle.....
> > Apples to oranges....Lincoln's 60% duty cycle is rated at 150 amps at 24
> > volts, while Miller's 210 is 160 amps at 24.5 volts.
> > So here's a break down of their performance at 30% duty cycles (max
> > range)...
> > Lincoln 200 Power Mig--- 200 amps (max range) at 22 volts at 30% duty
cycle
> > MillerMatic 210--- 210 amps (max range) at 22 volts at 30% duty cycle
> > How the two companies advertise their ratings are different. I don't
know
> > what the "CV" Output Rating is that Lincoln advertises their 30% duty
cycle
> > at. The 60% duty cycle is the Specified Rating through the U.S. and
Canadian
> > Standards Association.
> > Either way you look at it , the Miller is the more powerful machine.....
> > Brett Kinch
> > Rock-Quip
> > www.rock-quip.rockcrawler.com
> >
> >
> >
> > > That may be but the output range of the Lincoln is 200 amps, albeit at
> > > reduced duty cycle whereas the Miller's output rating is only 160
amps.
> > > These figures are from www.lincolnelectric.com and www.millerwelds.com
> > >
> > > Lee
> > > ---- Original Message -----
> > > From: "Brett Kinch" <kinchx4_at_earthlink.net>
> > > To: "bfix" <mail_at_broncofix.com>; "ebml" <ebml_at_bronco.com>
> > > Sent: Wednesday, February 06, 2002 7:21 PM
> > > Subject: Re: [Bfix] [EBML] Welder recomendations
> > >
> > >
> > > > The Output Range of the Miller 210 is 30-210 amps. The Output Range
of
> > > the
> > > > Lincoln 200 is 30-200 amps.
> > > > The Rated Output at 60% duty cycle is 160 amps for the Miller 210,
and
> > 150
> > > > amps for the Lincoln 200.....
> > > > Brett Kinch
> > > > Rock-Quip
> > > > www.rock-quip.rockcrawler.com
> > > >
> > > >
> > > >
> > > > > You'd better check your facts again Brett. The Miller's "Output
> > Range"
> > > is
> > > > > 210, not the actual or rated output which is only 160 amps whereas
the
> > > > > Lincoln is 200. Both companies try to mislead you a bit.
(Lincoln
> > does
> > > > the
> > > > > same on their smaller welders.) They can get away with this as
long
> > as
> > > > they
> > > > > show the "Rated Output" somewhere. Buyer beware...
> > > > >
> > > > > Lee Wilson
> > > > > Houston, TX
> > > > > ----- Original Message -----
> > > > > From: "Brett Kinch" <kinchx4_at_earthlink.net>
> > > > > To: "bfix" <mail_at_broncofix.com>; "ebml" <ebml_at_bronco.com>
> > > > > Sent: Wednesday, February 06, 2002 6:02 PM
> > > > > Subject: Re: [Bfix] [EBML] Welder recomendations
> > > > >
> > > > >
> > > > > > The185 has been replaced by the 210 which is more powerful than
> > > > Lincoln's
> > > > > > 200.
> > > > > > Rated Output:
> > > > > > Miller 210--160 amps at 24.5 volts at 60% duty cycle
> > > > > > Lincoln 200-- 150 amps at 24 volts at 60% duty cycle
> > > > > > Interestingly, my Miller 185 has the same rated output as the
> > Lincoln
> > > > 200
> > > > > > except for 1 volt....
> > > > > > Miller 185-- 150 amps at 23 volts at 60% duty cycle
> > > > > > Hmmmm.............
> > > > > > Brett Kinch
> > > > > > Rock-Quip
> > > > > > www.rock-quip.rockcrawler.com
> > > > > >
> > > > > >
> > > > > >
> > > > > > > Kevin, good choice!!!!!! Ive used the Miller 185 and it cannot
> > hang
> > > > with
> > > > > > my
> > > > > > > lincoln power mig. Mine cost me 50 bucks more than the 185 and
its
> > a
> > > > > true
> > > > > > > quality unit. And like Brian said, its got that cool Nascar
> > sticker
> > > on
> > > > > > it!!!
> > > > > > > :)
> > > > > > >
> > > > > > >
> > > > > > > Clint
> > > > > > > ----- Original Message -----
> > > > > > > From: "Kevin Lackey" <lackkevi_at_inconnu.isu.edu>
> > > > > > > To: "Mike Bowlin" <live2wheel_at_msn.com>
> > > > > > > Cc: <EBML_at_bronco.com>; <mail_at_broncofix.com>
> > > > > > > Sent: Wednesday, February 06, 2002 1:19 PM
> > > > > > > Subject: Re: [Bfix] [EBML] Welder recomendations
> > > > > > >
> > > > > > >
> > > > > > > > I think after looking around I am going to get a Licoln
PowerMig
> > > > 200.
> > > > > I
> > > > > > > > found them for $1057.32 at www.weldingmart.com with free
> > delivery.
> > > I
> > > > > > just
> > > > > > > > have to decide between at 200 amp and the 255 amp
unit........ a
> > > > > little
> > > > > > > > more money.
> > > > > > > > Kevin
> > > > > > > >
> > > > > > > > --
> > > > > > > > Pereant, inquit, qui ante nos nostra dixerunt.
> > > > > > > >
> > > > > > > >
> > > > > > > >
> > > > >
> > <><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><>
> > > > > > > > For Broncofix list addition and removal, go to
> > > > > http://www.broncofix.com
> > > > > > > > Check out our new message board at
> > > http://www.broncofix.com/board!!!
> > > > > > > > For additional assistance, email the admin at
> > admin_at_broncofix.com
> > > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > ######################################################################
> > > > > > > Attention:
> > > > > > > This e-mail message is privileged and confidential. If you are
not
> > > the
> > > > > > > intended recipient please delete the message and notify the
> > sender.
> > > > > > > Any views or opinions presented are solely those of the
author.
> > > > > > >
> > > ######################################################################
> > > > > > >
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
############################################################################
> > > > > > #########
> > > > > > > This e-mail message has been scanned for Viruses and Content.
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
############################################################################
> > > > > > #########
> > > > > > >
> > > > > > >
> > > >
<><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><>
> > > > > > > For Broncofix list addition and removal, go to
> > > > http://www.broncofix.com
> > > > > > > Check out our new message board at
> > http://www.broncofix.com/board!!!
> > > > > > > For additional assistance, email the admin at
admin_at_broncofix.com
> > > > > > >
> > > > > >
> > > > > > ------------------------------
> > > > > > Early Bronco Mailing List (EBML)
> > > > > > Unsubscribe: majordomo_at_bronco.com unsubscribe EBML
> > > > youremailid_at_yourisp.com
> > > > > > in the messagebody.
> > > > > > To modify your account (switch to digest or to real-time), goto:
> > > > > > http://mail.bronco.com/cgi-bin/mj_wwwusr/domain=bronco.com/EBML.
> > > > > > Admin address: EBML-owner_at_bronco.com
> > > > > >
> > > > >
> > > > > ------------------------------
> > > > > Early Bronco Mailing List (EBML)
> > > > > Unsubscribe: majordomo_at_bronco.com unsubscribe EBML
> > > youremailid_at_yourisp.com
> > > > > in the messagebody.
> > > > > To modify your account (switch to digest or to real-time), goto:
> > > > > http://mail.bronco.com/cgi-bin/mj_wwwusr/domain=bronco.com/EBML.
> > > > > Admin address: EBML-owner_at_bronco.com
> > > > >
> > > >
> > > >
> > > >
<><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><>
> > > > For Broncofix list addition and removal, go to
http://www.broncofix.com
> > > > Check out our new message board at http://www.broncofix.com/board!!!
> > > > For additional assistance, email the admin at admin_at_broncofix.com
> > > >
> > >
> > >
> > >
<><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><>
> > > For Broncofix list addition and removal, go to
http://www.broncofix.com
> > > Check out our new message board at http://www.broncofix.com/board!!!
> > > For additional assistance, email the admin at admin_at_broncofix.com
> > >
> >
> > ------------------------------
> > Early Bronco Mailing List (EBML)
> > Unsubscribe: majordomo_at_bronco.com unsubscribe EBML
youremailid_at_yourisp.com
> > in the messagebody.
> > To modify your account (switch to digest or to real-time), goto:
> > http://mail.bronco.com/cgi-bin/mj_wwwusr/domain=bronco.com/EBML.
> > Admin address: EBML-owner_at_bronco.com
> >
>
>
> <><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><><>
> For Broncofix list addition and removal, go to http://www.broncofix.com
> Check out our new message board at http://www.broncofix.com/board!!!
> For additional assistance, email the admin at admin_at_broncofix.com
>
Received on Thu Feb 07 2002 - 07:36:36 MST


Email us at: info@bronco.com
Many thanks to our contributors.
© 1996 - 2016 www.Bronco.com